Honda Prelude Forum banner


  1. EuroR H22a EGR Plate Gasket

    I am in need of the gasket for the EGR Plate not valve for the EuroR intake manifold. My name is Kyle, thanks for assistance!
  2. My 4th gen prelude build

    Ask ?
  3. 1999 prelude ecu question

    5th Gen
    So to start off, I was just switching through the gears when my battery light came on and my car died. It cranks over but doesn't start. Took it to a mechanic after replacing parts we thought it could've been and he couldn't find any mechanical issues with it. Still won't start. I was told it...
  4. Any intrest in a 4th gen prelude?

    4th Gen
    i'm looking to sell my 4th gen prelude, it's a 1993 with a JDM H22a and the bottom end of the motor has been built with mahle pistons and eagle rods, and has a GT3582r turbo on it, also running 780cc injectors, i have also put new wheel bearings and brakes on the front and back, and have done...
  5. Power band drops at 4500 rpm- HELP

    5th Gen
    Help! Power band drops at 4500 rpm (VETC engage point) When my car hits 4500 RPM (When VTEC is supposed to kick in) the power band completely dies like there's a rev limiter. And this happens only when there's some kind of load on the engine, any other time, it's fine. Can someone tell me...
  6. H22a oil pump

    H22A/1+ & H23A/1+ Specific Information
    Ok so before anyone says it I have looked repeatedly for the answer and its different everywhere I look. Are all h22 oil pumps the same. I have an H22a and need to know if an obd1 h22a1 oil pump will work or no. If no WHERE can I find a jdm H22a oil pump for sale
  7. H22a egr check engine light on

    5th Gen
    my car is a 98 Prelude Base model with 4th gen h22a swap. always had an egr cel since the swap and ive replaced everything under the sun related to the egr sustem and still getting the code. not really trying to remove the manifold to clean out the ports cause I've heard it doesnt always cure...
  8. Whats up PP!?!?!

    Hey everybody my names Stephin/Seven and im from Los Angeles, CA . I own a 1998 US BB6 BASE (5th gen so everyone knows haha) that I purchased roughly 3 years ago after wanting to get my hands on one for about 8 years (im 26 btw). Ive loved Preludes since the first time I saw one in highschool...
  9. H22A Engine non-interference at non-VTEC rpm

    4th Gen
    A couple of weeks ago I replaced all oil seals due to a camshaft seal leak. I did full timing belt service (tensioners, water pump, all belts etc) at the same time. Somehow I made a mistake and tightened the timing belt tensioning pulley (no 18 here...
  10. engine and speedosurge

    5th Gen
    I recently swapped a h22a into my bb6, when it the engine surges as well as the speedometer. Any ideas??????:silly:
  11. bb6 h22a swap parts????

    5th Gen
    Heys guys I got one last question (for now) about swapping a h22a into my bb6. What parts do i have to swap over from the old h22a4 in order to get it to pass smog and run. I know i have to swap out the dizzy and a few other parts, but i haven't been able to find a list or how to. I just want to...
  12. H22A JDM Engine

    5th Gen
    I have a knock in my 2000 prelude. I'm looking to replace the motor with the jam h22a. Anyone know of any good places to buy it through????:mrgreen:
  13. Help! Transmission rebuild questions m2a4

    4th Gen
    So I just started putting my trans back together the other day after buying a synchrotech master rebuild kit and it did not come with a mainshaft clutch housing bearing and mine is definitely shot. The one I pulled from the trans has two o rings on the outer radius. Should I be worried that on...
  14. H22A Swap Crank Pulley Issue and Questions

    5th Gen
    So my brother and I recently picked up a clean-titled 2000 Base with an H22A swap, for a decent price, intending for it to be a daily for my brother. We knew the car had some issues, the previous owner was very up-front about it, and my brother claimed to be prepared for it. Anyway, so the...
  15. what 4th gen prelude is best/bettr for H22a

    4th Gen
    :?:So im leaving san diego to go to alaska in 10 days and work the summer. Im doing it to come home and get my first prelude.(nothing more than $3k?ish)I've been doing weeks of research and i know i want an H22a motor, but im not sure what model lude(--year, if it matters. Sticking with 4th gen...
  16. JDM H22A Head on a USDM H22A4 block?

    4th Gen
    I am sure this has been discussed before somewhere but I have a few questions regarding pairing a JDM H22A head onto a USDM H22A4 block. I have a 94 Prelude that has a CAI and was caught in a flash flood and well, you can guess what happened there... After getting all the water out and trying...
  17. what can i do to upgrade my engine?

    4th Gen
    i just bought a JDM h22a and im about to put it in my 93 prelude, i was wondering what are good upgrades to do? i wanted a bigger throttle body but i heard it doesnt do much, is that true?
  18. what turbo should i get for a 1993 prelude?

    4th Gen
    i just bought my prelude and put a JDM h22a in, im looking at what turbo would be good. could someone post a few reasonably priced turbos that would be good. would a T3 T4 T04E be good? thanks!
  19. Will this h22a block work with ATTS

    i have a SH that i bought with a junk engine (rod through cylinderwall) I might possibly be buying this long block setup. The serial # is 1007808 and the VC is Red. Now im totally lost. from what it appears the serial # is stating the block is from like 1991 i think. i dunno ive literally been...
  20. Braided Clutch line?

    4th Gen
    Ok so im in the process of going from my old H23 Auto trans to a H22A Manual. and im down to having to run a new hard line from the clutch master cyl. And was wondering if it would be easier to buy a braided clutch line from master cyl to slave cyl. And if anyone knows where you can buy braided...