engine swap

Let’s say hypothetically, if I were to engine swap a 3rd gen 1990 Honda prelude. What would be one of the best and or the most affordable (doesn’t have to be dirt cheap just not above $9,000 or $10,000) engine to swap?

I have 4th gen prelude with h22a4 engine and I wondering what engines have people swap there engins and if anyone had swap there engine for h22a4 to h22a7

Hey, so I'm pretty young at 19, and I bought my first car which is the base 2001 Prelude automatic, and I would like to know what type of engine swap should I do in the future to the car. I love the car and I want to keep it for a long time. I hear the transmission on these cars go out at 100k...

First time posting here, I'm looking to do an engine swap in my 1987 DX and I'm thinking of doing a b20b, I'm wondering if anyone has done that swap in their 2g prelude and if you have done any swap in general or know one that works better I'd love to hear about it. I haven't been able to find...

This might be a stupid question. Im planning to do engine swap to my lude when i have resources to do it. I want to swap my current f20a4 to a f20b bluetop so my question is this: does they share same engine mounts or do i have to fabricate new mounts or something? Thanks!

Hey there’s guys I have usdm 1995 Prelude with a F22a1 motor under hood I’m currently working on getting a jdm h22a with lsd tranny I just wondering what kind of trouble I’m gonna be running into the swap?can I use f22 wiring harnesses I know I will have to run vtec to ecu to vtec solenoid...

I've had this thing for a few weeks now. It's a 2010 C350 Sport. Unfortunately it was time for something more reliable and in better condition. Last October the balance shaft seal blew out on my Prelude at highway speed. It emptied all the oil within seconds and destroyed my cylinder...

My Tranny just seized up so I am pulling the motor (already in the process) but this is my first time so looking for some extra advice so I don not ruin anything as this is supposed to be my Daily Driver. At this point I have: -pulled the axles -Disconnected the wire harness -unbolted A/C...

My Tranny just seized up so I am pulling the motor (already in the process) but this is my first time so looking for some extra advice so I don not ruin anything as this is supposed to be my Daily Driver. At this point I have: -pulled the axles -Disconnected the wire harness -unbolted A/C...

im curious but what would be the best engine to swap into my 89 prelude and can it be vtec ??

I am looking to swap my block in my '93 Prelude. I'm looking to either go with either the: 2000 H23A DOHC VTECH Bluetop Long Block H22A Long Block or the F20B Long Block (Manual Version) I seem to notice more people going with the H22A but was wanting some more opinions and reasons why. Thanks all!

I currently have a huge paperweight H23a in my 95 Prelude. I have been dead set on the H22A, but I'm wondering how hard it would be to put in a K24. I am very new to the Honda building realm. I currently have an automatic transmission, and a helms manual. I bought the manual shifter for my car...

Okay, So here begins my adventure in the world of engine swaps. I've got a sh with a blown motor. thrown rod. too much mileage to keep the trans so I'm going with a JDM swap. I've done a lot of reading and its all about spaced out so I wanted to come to the board here for some confirmation and...

I recently did a engine swap and fcukwithmeprelude was kind enough to help me, everythign turned out well and the engine sound good just probly need a valve adjustment. http://www.preludepower.com/forums/showthread.php?p=1950455 I test drive the car around the block and every thign was fine...

swapping a d16a6, does anybody kno if this is at all possible even with correct wiring harness and mounts I own a 91 Prelude Si b21a1...Rings are bad and tranny is slippin i bought a d16a6 from a junkyard manuel 5 speed SOHC of course, pgmfi jus like the lude i...

i know for a fact that one has an egr and other has valve relief but can i directly swap one for the other without swapping the computer? what are the pros and cons or are they the same exact engine?